View CS5203-1_130601.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CS5203 -1
CS5203-1
3A Adjustable Linear Regulator
Description
The CS5203-1 linear regulator provides 3A at adjustable output voltages with an accuracy of 1.5%. The device uses two external resistors to set the output voltage within a 1.25V to 5.5V range. The regulator is intended for use as a post regulator and microprocessor supply. The fast loop response and low dropout voltage make this regulator ideal for applications where low voltage operation and good transient response are important. The circuit is designed to operate with dropout voltage less than 1.4V at 3A output current. Device protection includes overcurrent and thermal shutdown. The CS5203-1 is pin compatible with the LT1085 family of linear regulators but has lower dropout voltage. The regulator is available in TO-220 and surface mount D2 packages.
Features
s Output Current to 3A s Output Accuracy to 1.5% Over Temperature s Dropout Voltage (typical) 1.2V @ 3A s Fast Transient Response s Fault Protection Current Limit Thermal Shutdown
Application Diagram
Package Options
3L TO-220
Tab (VOUT)
3L D2PAK
Tab (VOUT)
5.0V
VIN
VOUT CS5203-1
Adj
124W 1% 3.3V @ 3A
1
10mF 5V
22mF 5V 0.1mF 5V 200W 1%
1
CS5203 -1 1 Adj 2 VOUT (Tab) 3 VIN
Consult factory for fixed output voltage versions.
Cherry Semiconductor Corporation 2000 South County Trail, East Greenwich, RI 02818 Tel: (401)885-3600 Fax: (401)885-5786 Email: info@cherry-semi.com Web Site: www.cherry-semi.com
Rev. 9/17/97
1
A
Company
CS5203 -1
Absolute Maximum Ratings Supply Voltage, VIN .....................................................................................................................................................................7V Operating Temperature Range................................................................................................................................-40C to 70C Junction Temperature ............................................................................................................................................................150C Storage Temperature Range ..................................................................................................................................-60C to 150C ESD Damage Threshold............................................................................................................................................................2kV Lead Temperature Soldering Wave Solder (through hole styles only) .....................................................................................10 sec. max, 260C peak Reflow (SMD styles only) ......................................................................................60 sec. max above 183C, 230C peak
Electrical Characteristics: CIN = 10F, COUT = 22F Tantalum, VOUT + VDROPOUT < VIN < 7V, 0C TA 70C, TJ +150C,
unless otherwise specified, Ifull load = 3A. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
s Adjustable Output Voltage (CS5203-1) Reference Voltage (Notes 1 and 2) Line Regulation Load Regulation (Notes 1 and 2) Dropout Voltage (Note 3) Current Limit Adjust Pin Current Thermal Regulation (Note 5) Ripple Rejection (Note 5) Thermal Shutdown (Note 6) Thermal Shutdown Hysteresis (Note 6) VINVOUT=1.5V; VAdj = 0V 10mAIOUT3A 2VVINVOUT5.75V; IOUT=10mA VINVOUT=2V; 10mAIOUT3A IOUT=3A VINVOUT=3V; TJ 25C VINVOUT=3V; IOUT=10mA 30ms pulse; TA=25C f=120Hz; IOUT=3A; VINVOUT=3V; VRIPPLE=1VPP 150 3.1 1.235 (-1.5%) 1.254 0.02 0.04 1.15 4.6 0.6 50 0.002 80 180 210 25 2.0 100 0.020 1.273 (+1.5%) 0.20 0.4 1.40 V % % V A mA A %/W dB C C
Minimum Load Current (Note 4) VIN=7V; Vadj=0
Note 1: Load regulation and output voltage are measured at a constant junction temperature by low duty cycle pulse testing. Changes in output voltage due to temperature changes must be taken into account separately. Note 2: Specifications apply for an external Kelvin sense connection at a point on the output pin 1/4O from the bottom of the package. Note 3: Dropout voltage is a measurement of the minimum input/output differential at full load. Note 4: Minimum load current is defined as the minimum output current required to maintain regulation. The reference resistor in the output divider is usually sized to fulfill the minimum load current requirement. Note5: Guaranteed by design, not 100% functionally tested in production. Note 6: Guaranteed by design, not 100% parametrically tested in production. However, every part is subject to functional testing for thermal shutdown.
Package Pin Description
PACKAGE PIN # PIN SYMBOL FUNCTION
D2PAK 1 2 3
TO-220 1 2 3 Adj VOUT VIN Adjust pin (low side of the internal reference). Regulated output voltage (case) Input voltage.
2
CS5203 -1
Block Diagram
V OUT V IN
Output Current Limit Thermal Shutdown + Error Amplifier Adj
Bandgap Reference
Typical Performance Characteristics
1.20 Reference Voltage Deviation (%) 1.15 1.10 Dropout Voltage (V) 1.05 1.00 0.95 0.90 0.85 0.80 0.75 0.00 0.30 0.60 0.90 1.20 1.50 1.80 2.10 Output Current (A) 2.40 2.70 3.00 TCASE = 25C
TCASE
+0.3
+0.2
+0.1
= 0C
0
-0.1
TCASE = 125C
-0.2 -0.3 0 30 60 TJ (C) 90 120
Dropout Voltage vs. Output Current
Bandgap Reference Voltage Deviation vs. Temperature
90.00 80.00 70.00 60.00 50.00 40.00 30.00 20.00 10.00
101 102 103 104 105 106 Minimum Load Current (mA)
0.65
0.60 TCASE = 0C 0.55 TCASE = 25C 0.50 TCASE = 125C
Ripple Rejection (dB)
0.45
0.40 1.00 2.00 3.00 4.00 5.00 VIN - VOUT (V) 6.00 7.00 8.00
Frequency (Hz)
Ripple Rejection vs. Frequency
Minimum Load Current vs VIN-VOUT
3
CS5203 -1
Typical Performance Characteristics: continued
75
68.00 66.00
Adjust Pin Current (mA) TCASE = 125C
Adjust Pin Current
64.00 62.00 60.00
TCASE = 25C
65 IAdj (mA) 55
58.00 56.00
TCASE = 0C 2.00 3.00 4.00 5.00 6.00 7.00 8.00
45 0 30 60 TA(C) 90 120
54.00 1.00
VIN - VOUT (V)
Adjust Pin Current vs. Temperature
Adjust Pin Current vs. VIN -VOUT
70.00 68.50
+200
67.00 Adjust Pin Current (mA) 65.50 64.00 62.50 61.00 59.50 58.00 56.50 55.00 0.0 0.3 0.6 0.9 1.2 1.5 IOUT (A) 1.8 2.1 2.4 2.7 3.0
DVOUT 0 (mV) -200
-200 3 I(A) 1 0 0
VIN = 5V VOUT = 3.3V CIN = 100mF COUT = 10mF Tantalum
5 Time (ms)
10
Adjust Pin Current vs Output Current
Transient Response
6.00 5.00
4.00
ISC(A)
3.00 2.00
1.00 0.00 1.00 2.00 3.00 4.00 5.00 6.00 7.00
VIN-VOUT (V)
Short Circuit Current vs VIN-VOUT
4
CS5203 -1
Applications Information The CS5203-1 linear regulator provides adjustable voltages at currents up to 3A. The regulator is protected against overcurrent conditions and includes thermal shutdown. The CS5203-1 has a composite PNP-NPN output transistor and requires an output capacitor for stability. A detailed procedure for selecting this capacitor is included in the Stability Considerations section.
Adjustable Operation
ages in excess of 7V. The main considerations in such a design are power-up and short circuit capability. In most applications, ramp-up of the power supply to VIN is fairly slow, typically on the order of several tens of milliseconds, while the regulator responds in less than one microsecond. In this case, the linear regulator begins charging the load as soon as the VIN to VOUT differential is large enough that the pass transistor conducts current. The load at this point is essentially at ground, and the supply voltage is on the order of several hundred millivolts, with the result that the pass transistor is in dropout. As the supply to VIN increases, the pass transistor will remain in dropout, and current is passed to the load until VOUT reaches the point at which the IC is in regulation. Further increase in the supply voltage brings the pass transistor out of dropout. The result is that the output voltage follows the power supply ramp-up, staying in dropout until the regulation point is reached. In this manner, any output voltage may be regulated. There is no theoretical limit to the regulated voltage as long as the VIN to VOUT differential of 7V is not exceeded. However, the possibility of destroying the IC in a short circuit condition is very real for this type of design. Short circuit conditions will result in the immediate operation of the pass transistor outside of its safe operating area. Overvoltage stresses will then cause destruction of the pass transistor before overcurrent or thermal shutdown circuitry can become active. Additional circuitry may be required to clamp the VIN to VOUT differential to less than 7V if failsafe operation is required. One possible clamp circuit is illustrated in figure 2; however, the design of clamp circuitry must be done on an application by application basis. Care must be taken to ensure the clamp actually protects the design. Components used in the clamp design must be able to withstand the short circuit condition indefinitely while protecting the IC.
EXTERNAL SUPPLY
The CS5203-1 has an output voltage range of 1.25V to 5.5V. An external resistor divider sets the output voltage as shown in Figure 1. The regulator maintains a fixed 1.25V (typical) reference between the output pin and the adjust pin. A resistor divider network R1 and R2 causes a fixed current to flow to ground. This current creates a voltage across R2 that adds to the 1.25V across R1 and sets the overall output voltage. The adjust pin current (typically 50A) also flows through R2 and adds a small error that should be taken into account if precise adjustment of VOUT is necessary. The output voltage is set according to the formula:
VOUT = VREF R1 + R2 + IAdj R2 R1 The term IAdj R2 represents the error added by the adjust pin current. R1 is chosen so that the minimum load current is at least 2mA. R1 and R2 should be the same type, e.g. metal film for best tracking over temperature. While not required, a bypass capacitor between the adjust pin and ground will improve ripple rejection and transient response. A 0.1F tantalum capacitor is recommended for Ofirst cutO design. Type and value may then be varied to optimize performance vs. price.
(
)
VIN
VIN C1
VIN
VOUT
VOUT
VAdj
VOUT
CS5203-1
Adj
VREF R1 C2
VOUT
IAdj CAdj R2
Figure 2. Short Circuit Protection Circuit for High Voltage Application.
Stability Considerations
Figure 1. Resistor divider scheme.
The 5203-1 linear regulator has an absolute maximum specification of 7V for the voltage difference between VIN and VOUT. However, the IC may be used to regulate volt-
The output or compensation capacitor helps determine three main characteristics of a linear regulator: start-up delay, load transient response and loop stability. The capacitor value and type is based on cost, availability, size and temperature constraints. A tantalum or aluminum
5
CS5203 -1
Applications Information: continued electrolytic capacitor is best, since a film or ceramic capacitor with almost zero ESR can cause instability. The aluminum electrolytic capacitor is the least expensive solution. However, when the circuit operates at low temperatures, both the value and ESR of the capacitor will vary considerably. The capacitor manufacturersO data sheet provides this information. A 22F tantalum capacitor will work for most applications, but with high current regulators such as the CS5203-1 the transient response and stability improve with higher values of capacitor. The majority of applications for this regulator involve large changes in load current so the output capacitor must supply the instantaneous load current. The ESR of the output capacitor causes an immediate drop in output voltage given by: AEV = AEI ESR For microprocessor applications it is customary to use an output capacitor network consisting of several tantalum and ceramic capacitors in parallel. This reduces the overall ESR and reduces the instantaneous output voltage drop under load transient conditions. The output capacitor network should be as close as possible to the load for the best results.
Protection Diodes Output Voltage Sensing
Since the CS5203-1 is a three terminal regulator, it is not possible to provide true remote load sensing. Load regulation is limited by the resistance of the conductors connecting the regulator to the load. For the adjustable regulator, the best load regulation occurs when R1 is connected directly to the output pin of the regulator as shown in Figure 4. If R1 is connected to the load, RC is multiplied by the divider ratio and the effective resistance between the regulator and the load becomes RC R1 + R2 R1
(
)
conductor parasitic resistance
RC = conductor parasitic resistance
VIN
VIN
VOUT
RC
CS5203-1
R1 Adj
RLOAD
When large external capacitors are used with a linear regulator it is sometimes necessary to add protection diodes. If the input voltage of the regulator gets shorted, the output capacitor will discharge into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage and the rate at which VIN drops. In the CS5203-1 linear regulator, the discharge path is through a large junction and protection diodes are not usually needed. If the regulator is used with large values of output capacitance and the input voltage is instantaneously shorted to ground, damage can occur. In this case, a diode connected as shown in Figure 3 is recommended.
R2
Figure 4. Grounding scheme for the adjustable output regulator to minimize parasitic resistance effects.
Calculating Power Dissipation and Heat Sink Requirements
IN4002 VIN C1 VIN
(optional) VOUT VOUT
The CS5203-1 linear regulator includes thermal shutdown and current limit circuitry to protect the device. High power regulators such as these usually operate at high junction temperatures so it is important to calculate the power dissipation and junction temperatures accurately to ensure that an adequate heat sink is used. The case is connected to VOUT on the CS5203-1 , and electrical isolation may be required for some applications. Thermal compound should always be used with high current regulators such as these. The thermal characteristics of an IC depend on the following four factors: 1. Maximum Ambient Temperature TA (C) 2. Power dissipation PD (Watts) 3. Maximum junction temperature TJ (C) 4. Thermal resistance junction to ambient RQJA (C/W) These four are related by the equation
CS-5203-1
R1 Adj C2
CAdj
R2
Figure 3. Protection diode scheme for large output capacitors.
6
CS5203 -1
Applications Information: continued TJ = TA + PD RQJA (1) 3. Thermal Resistance of the Heat Sink to the ambient air, RQSA (C/W) These are connected by the equation: RQJA = RQJC + RQCS + RQSA (3)
The maximum ambient temperature and the power dissipation are determined by the design while the maximum junction temperature and the thermal resistance depend on the manufacturer and the package type. The maximum power dissipation for a regulator is:
The value for RQJA is calculated using equation (3) and the result can be substituted in equation (1). PD(max)={VIN(max)VOUT(min)}IOUT(max)+VIN(max)IQ where VIN(max) is the maximum input voltage, VOUT(min) is the minimum output voltage, IOUT(max) is the maximum output current, for the application IQ is the maximum quiescent current at IOUT(max). A heat sink effectively increases the surface area of the package to improve the flow of heat away from the IC and into the surrounding air. Each material in the heat flow path between the IC and the outside environment has a thermal resistance. Like series electrical resistances, these resistances are summed to determine RQJA, the total thermal resistance between the junction and the surrounding air. 1. Thermal Resistance of the junction to case, RQJC (C/W) 2. Thermal Resistance of the case to Heat Sink, RQCS (C/W) (2) The value for RQJC is 3.5u C/W as a single figure for a given package type based on an average die size. For a high current regulator such as the CS5203-1 the majority of the heat is generated in the power transistor section. The value for RQSA depends on the heat sink type, while RQCS depends on factors such as package type, heat sink interface (is an insulator and thermal grease used?), and the contact area between the heat sink and the package. Once these calculations are complete, the maximum permissible value of RQJA can be calculated and the proper heat sink selected. For further discussion on heat sink selection, see application note OThermal Management for Linear Regulators.O
7
CS5203 -1
Package Specification
PACKAGE DIMENSIONS IN mm (INCHES) 3 Lead D2PAK (DP)
10.31 (.406) 10.05 (.396) 1.68 (.066) 1.40 (.055) 1.40 (.055) 1.14 (.045)
PACKAGE THERMAL DATA
Thermal Data RQJC typ RQJA typ
3L TO-220 3.5 50
3L D2PAK 3.5 10 - 50*
uC/W uC/W
*Depending on thermal properties of substrate. RQJA = RQJC + RQCA
8.53 (.336) 8.28 (.326) 15.75 (.620) 14.73 (.580) 2.74(.108) 2.49(.098) 1.40 (.055) 1.14 (.045) 0.91 (.036) 0.66 (.026) 2.54 (.100) REF .254 (.010) REF 2.79 (.110) 2.29 (.090)
4.57 (.180) 4.31 (.170)
0.10 (.004) 0.00 (.000)
3 Lead TO-220 (T) Straight
10.54 (.415) 9.78 (.385) 2.87 (.113) 2.62 (.103) 3.96 (.156) 3.71 (.146)
4.83 (.190) 4.06 (.160)
1.40 (.055) 1.14 (.045)
6.55 (.258) 5.94 (.234)
14.99 (.590) 14.22 (.560)
1.52 (.060) 1.14 (.045) 14.22 (.560) 13.72 (.540) 1.40 (.055) 1.14 (.045)
6.17 (.243) REF
1.02 (.040) 0.63 (.025) 2.79 (.110) 2.29 (.090) 5.33 (.210) 4.83 (.190) 0.56 (.022) 0.38 (.014) 2.92 (.115) 2.29 (.090)
Ordering Information
Part Number CS5203-1GT3 CS5203-1GDP3 CS5203-1GDPR3
Rev. 9/17/97
Type 3A, adj. output 3A, adj. output 3A, adj. output
Description 3 L TO-220 Straight 3 L D2PAK 3 L D2PAK (tape & reel) 8
Cherry Semiconductor Corporation reserves the right to make changes to the specifications without notice. Please contact Cherry Semiconductor Corporation for the latest available information.
(c) 1999 Cherry Semiconductor Corporation

▲Up To Search▲

Price & Availability of CS5203-1

	To Download CS5203-1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .